Out of the box the CR2300 will read the following bar codes:
Sufx Enter
The default seng on the CR2300 has Sux Enter disabled. To enable
Sux Enter, scan the following conguraon code. For RS232 Sengs,
please refer to the CR2300 Conguraon Guide.
Press and hold a buon or trigger on the CR2300, the two blue bars
eming from the reader are used for targeng. Center the blue bars in
the middle of a bar code. When the bar code is in the reader’s eld of
view and at the opmal distance (4” from the bar code) , the reader will
automacally read the code.
The CR2300 will beep and the good read indicator will ash green to
indicate a ‘good read’ has occurred. (Figure 12)
Using the CR2300
CR2300 Default Settings
Aztec
Codabar
Code 39
Code 93
Code 128
Data Matrix
Data Matrix Rectangle
GS1 DataBar
Int 2 of 5
MSI Plessey
PDF417
QR Code
UPC/EAN/JAN
Sux Enter - USB
Fuel Gauge Battery Status
Check Baery Life
Press the fuel gauge buon (Figure 10) to determine remaining baery life. If the baery has less
then 10% capacity, the rst LED will ash rapidly. For 25% or greater capacity, the LEDs will ash
ON for 4 seconds.
Fuel Gauge Status Indicator While Charging
If the baery has less then 10% capacity, the rst LED will ash rapidly while charging. For 25% or
greater capacity, the LEDs will ash ON for 4 seconds and OFF for 1 second. (Figure 11)
Fuel Gauge
Indicators
Figure 10
Fuel Gauge
Buon
Baery Life
<10% Rapid Flashing
<25% ON
25-50% ON ON
50-75% ON ON ON
75%+ ON ON ON ON
To congure a CR2300 to read bar codes not
listed, download the CR2300 Conguraon
Guide from www.codecorp.com and scan
the appropriate ‘Enable’ bar code reading
symbology conguraon code.
Figure 11
Figure 12
Charge
Indicator
Battery Installation and Removal
Place the baery into the reader as shown in
Figure 6. Once in place, the baery will snap
and lock to indicate proper installaon. For
baery removal, slide the latch (Figure 7), to
unlock and release the baery.
Figure 6
Figure 7
Latch
Powering on the Reader
Press and hold either of the buons or
trigger for one second, to power on.
4. (Oponal) To mount the Charging Staon to a surface place the ‘This Side
Down’ (Figure 4) side of the weighted base onto the surface and secure
with screws. Note: Because surface types dier, screws are not included
to mount a Charging Staon to a surface. Place the Charging Staon on
top of the secured weighted base (Figure 3) and secure to the base with
the screws provided (Figure 3)
5. Plug the USB cable into the computer’s USB port or the power adapter
into the wall outlet.
Charging a CR2300
Baeries ship with approximately 50% baery life
and should be completely charged before inial use.
Approximate me to charge a depleted baery is 4
hours via USB cable and 2 1/2 hours via AC power
supply.
To charge a reader, remove the plasc ‘Remove
Before Use’ cap, and place the reader into the
Charging Staon. (Figure 9)
When the reader is seated correctly, the Charging
Indicator LED (Figure 9) will turn green.
Weighted Base Adapter Plate
The weighted base has the same pre-drilled mounng holes as the ECS-H and UMC Chargers.
Figure 4
Figure 5
Figure 8
Figure 9
www.codecorp.com
www.codecorp.com
Good Read
Indicator
(62 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals