Code Code Reader 1000 Specifications download pdf (Page 19)

Update

Quick Start

DEFAULT SETTINGS

RESTORE SYSTEM DEFAULTS

For the scanner to restore the factory defaults, you must have it read the “Restore

System Defaults” barcode. This is a normal setup barcode, and the scanner will respond

with two beeps (high-low tone).

 After reading the “Update” barcode, all the parameters of the scanner will return to

their default values.

Restore System

Defaults

Note: The system default value (if there is) for each setting is indicated by an asterisk

“*”.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 139 140

Scanner 1
IMPORTANT NOTICES 3
RELEASE NOTES 5
CONTENTS 7
INTRODUCTION 11
INSIDE THE PACKAGE 12
Introduction 13
SYMBOLOGIES SUPPORTED 14
QUICK START 17
ENTER CONFIGURATION MODE 18
EXIT CONFIGURATION MODE 18
DEFAULT SETTINGS 19
RESTORE SYSTEM DEFAULTS 19
Quick Start 21
 Refer to Appendix III 23
LIST THE CURRENT SETTINGS 24
Chapter 1 25
1.3.1 GOOD READ BEEP 27
1.3.2 FREQUENCY 27
1.4 SCAN MODES 28
Chapter 1 29
1.5 SCANNING TIMEOUT 32
 Laser mode 32
 Auto Off mode 32
 Auto Power Off mode 32
1.9 NEGATIVE BARCODES 35
Chapter 2 37
2.1 KEYBOARD WEDGE 38
Chapter 2 39
Selecting Output Interface 39
2.1.2 KEYBOARD SETTINGS 40
2.1.3 INTER-CHARACTER DELAY 48
2.2 RS-232 49
2.2.2 BAUD RATE 49
2.2.3 DATA BITS 50
2.2.4 PARITY 50
2.2.5 FLOW CONTROL 51
2.2.6 INTER-CHARACTER DELAY 51
2.3.3 BAR STATE 53
2.3.4 MODULE TIME 53
2.3.5 MARGIN TIME 54
Chapter 3 55
3.1 CODABAR 56
3.1.3 CLSI CONVERSION 57
3.2 CODE 25 – INDUSTRIAL 25 58
3.2.2 VERIFY CHECK DIGIT 59
3.2.3 TRANSMIT CHECK DIGIT 59
3.3 CODE 25 – INTERLEAVED 25 61
3.3.2 VERIFY CHECK DIGIT 62
3.3.3 TRANSMIT CHECK DIGIT 62
Chapter 3 63
Changing Symbology Settings 63
3.4 CODE 25 – MATRIX 25 64
3.4.2 VERIFY CHECK DIGIT 65
3.4.3 TRANSMIT CHECK DIGIT 65
3.5 CODE 39 67
3.5.2 VERIFY CHECK DIGIT 68
3.5.3 TRANSMIT CHECK DIGIT 68
3.6 CODE 93 69
3.7 CODE 128 69
3.8 EAN-8 70
3.8.1 CONVERT TO EAN-13 71
3.8.2 TRANSMIT CHECK DIGIT 71
3.9 EAN-13 72
3.9.1 CONVERT TO ISBN 73
3.9.2 CONVERT TO ISSN 73
3.9.3 TRANSMIT CHECK DIGIT 73
3.10.1 TRANSMIT CODE ID 74
3.10 GS1-128 (EAN-128) 74
3.11 MSI 75
3.11.1 VERIFY CHECK DIGIT 75
3.11.2 TRANSMIT CHECK DIGIT 75
3.12 FRENCH PHARMACODE 77
3.12.1 TRANSMIT CHECK DIGIT 77
3.13 ITALIAN PHARMACODE 78
3.13.1 TRANSMIT CHECK DIGIT 78
3.14 PLESSEY 79
3.14.1 CONVERT TO UK PLESSEY 79
3.14.2 TRANSMIT CHECK DIGIT 79
 GS1 DataBar Expanded 83
3.16 TELEPEN 85
3.17 UPC-A 86
3.17.1 CONVERT TO EAN-13 87
3.17.3 TRANSMIT CHECK DIGIT 87
3.18 UPC-E 88
3.18.4 TRANSMIT CHECK DIGIT 90
Chapter 4 91
4.3.2 CHANGE CODE ID 96
4.3.3 CLEAR CODE ID SETTINGS 97
4.4 LENGTH CODE 98
User Guide 100
Chapter 4 101
Defining Output Format 101
Chapter 5 103
5.1.2 EXCLUSIVE DATA EDITING 105
5.2.2 RESTORE DEFAULT FORMAT 108
5.3.1 APPLICABLE CODE TYPE 109
5.3.2 DATA LENGTH 113
5.4.1 TOTAL NUMBER OF FIELDS 115
5.4.2 FIELD SETTINGS 116
107 117
Field 2 Setting 117
109 119
Field 4 Setting 119
111 121
Additional Fields 121
Key Type Key Status 121
113 123
5.6 PROGRAMMING EXAMPLES 124
5.6.1 EXAMPLE I 124
SPECIFICATIONS 127
1100, 1105 129
Appendix I 131
EXAMPLE 132
Appendix II 133
KEY TYPE & STATUS 134
KEY TYPE 134
KEY STATUS 134
Appendix III 137
HEXADECIMAL SYSTEM 138
ASCII TABLE 139

Comments to this Manuals

No comments

Code Code Reader 1000 Specifications Page 19

Comments to this Manuals

Related products and manuals for Bar code readers Code Code Reader 1000