Code CR2 Cabled Quick Start User Manual download pdf

CR2 as a USB Keyboard

CR2 as a PS/2 Keyboard

1. Attach the USB cable (Figure 5 for cable types) to the CR2.

2. Connect the USB cable to a USB port (Figure 6) on the computer.

There is no need to power off the computer.

3. Once properly connected, the CR2 will power on and beep.

4. Scan the following code for USB Keyboard mode:

5. Scan the Save Settings code (M188_02) on page 3.

1. Power off the computer. If you disconnect the computer’s keyboard

while it is powered on, your computer will lock up.

2. Attach the PS/2 cable (see Figure 5 for cable types) to the CR2.

3. If you have a cabled keyboard, detach the keyboard cable from

the computer and connect that same connector to the female

connection on the CR2 PS/2 cable (Figure 7).

4. Now connect the male CR2 PS/2 connector into the keyboard port

on the computer (Figure 8).

1. Attach the RS-232 cable (see Figure 5 for cable types) to the CR2.

2. Connect the RS-232 cable to a serial port on the computer. There is no need to power off

the computer.

3. The RS-232 interface has an optional 5V/1.5A power supply. If you have a power supply,

plug the power supply adapter into the RS-232 cable and then plug the power adapter

into a wall socket.

4. Once properly connected, the CR2 will power on and beep.

5. Scan the following code for RS-232 (Serial) mode:

6. Scan the Save Settings code (M188_02) on page 3.

Note: To power on an uncabled CR2, the reader

must have a working battery (not a battery blank).

Press and hold red button for at least one second to

power on.

Figure 7

Figure 8

USB Keyboard Factory Reset

Figure 6

CR2 as a RS-232 (Serial)

All other USB settings (including Virtual COM

settings) may be found in the CR2 User Manual

at: www.codecorp.com/manuals.php

RS-232 Factory Default Settings

Mode: RS-232 One Way Mode Max Range

Baud Rate: 57600

Stop Bits: 1

Data Bits: 8

Parity: None

To save changes made to the CR2 conguration, scan the following code:

All other Serial settings can be found in the CR2 User Manual at: http://www.codecorp.com/manuals.php

Figure 5

PS/2 Keyboard Factory Reset

All other PS/2 settings may be found in the CR2

User Manual at: www.codecorp.com/manuals.php

5. Power on the computer. The CR2 is powered by the PS/2 port and does not require a power

supply.

6. Once properly connected, the CR2 will power on and beep.

7. Scan the following code for PS/2 Keyboard mode:

8. Scan the Save Settings code (M188_02) below.

RS-232 Factory Reset

RS-232 Mode

No Power Supply

Save Settings

Powering on a CR2

2 C002652_03_CR2_MIU_Cabled_Quickstart

C002652_03_CR2_MIU_Cabled_Quickstart

1 2

Summary of Contents

Page 1 - Powering on a CR2

CR2 as a USB KeyboardCR2 as a PS/2 Keyboard1. Attach the USB cable (Figure 5 for cable types) to the CR2.2. Connect the USB cable to a USB port (

Page 2 - Code Reader 2.0 - Cabled

Quickstart GuideHand Held CR2 - To install a cable directly to the CR2, correctly line up the 8-pin DIN connector into the back end of the unit. The a

Comments to this Manuals

No comments

Code CR2 Cabled Quick Start User Manual

Browse online or download User Manual for Equipment Code CR2 Cabled Quick Start. Code CR2 Cabled Quick Start User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment Code CR2 Cabled Quick Start